All public logs

Combined display of all available logs of Sensoray Technical Wiki. You can narrow down the view by selecting a log type, the username (case-sensitive), or the affected page (also case-sensitive).

• 08:40, 18 April 2017 JL (Talk | contribs) uploaded "File:PanelMountEncoder.jpg" (A panel mount incremental encoder with integrated pushbutton. This image was derived from Wikimedia Commons file Rot_enc.JPG and is licensed under Creative Commons Attribution-Share Alike 3.0 Unported.)
• 08:13, 18 April 2017 JL (Talk | contribs) uploaded "File:IncrementalEncoder.jpg" (An incremental encoder. This image was derived from Wikimedia Commons file Encoder_incremental Dynapar_B58N.jpg and is licensed under Creative Commons Attribution 4.0 International.)
• 07:36, 18 April 2017 JL (Talk | contribs) uploaded "File:TouchProbe.jpg" (A touch-trigger probe)
• 15:47, 29 March 2017 JL (Talk | contribs) uploaded a new version of "File:518 photo.jpg" (Reverted to version as of 17:48, 11 March 2016)
• 15:46, 29 March 2017 JL (Talk | contribs) uploaded a new version of "File:518 photo.jpg"
• 07:31, 1 March 2017 JL (Talk | contribs) uploaded a new version of "File:826 3Phase pwm.png" (fixed dio/counter routability)
• 16:42, 28 February 2017 JL (Talk | contribs) uploaded a new version of "File:826 quadrature gen.gif" (corrected dio/counter matching)
• 09:49, 22 February 2017 JL (Talk | contribs) uploaded "File:826 estop.gif" (A robust way to connect a 24VDC emergency-stop contact to model 826.)
• 08:18, 9 November 2016 JL (Talk | contribs) uploaded "File:826 ttl encoder.gif" (Wiring diagram showing how to connect two TTL/CMOS-compatible single-ended incremental encoders to the 826 board using counter channels 0 and 1.)
• 12:15, 4 November 2016 JL (Talk | contribs) uploaded "File:826 encoder FLT.png" (Using an 826 counter channel to monitor an incremental encoder's active-low FAULT output. The differential pair is swapped between line driver and receiver so that a disconnected or unpowered encoder will be recognized as a fault.)
• 12:02, 1 September 2016 JL (Talk | contribs) uploaded "File:SmartAD pinout.gif" (Connector pinout used by Sensoray Smart A/D boards (e.g., model 418, 419, 518, 618, 619). For each sensor channel x (in range 0:7), PHx/PLx supply excitation to a passive sensor (if needed) and SHx/SLx are the differential analog inputs. TREF and +12V ...)
• 10:54, 4 August 2016 JL (Talk | contribs) uploaded "File:Clock filter minimum.png" (826 counter timing diagram showing external clock filtering with zero filter delay (filter is disabled).)
• 10:53, 4 August 2016 JL (Talk | contribs) uploaded "File:Clock filter general.png" (826 counter timing diagram showing general case for external clock filtering.)
• 10:51, 4 August 2016 JL (Talk | contribs) uploaded a new version of "File:826 counter timing.png"
• 15:24, 3 August 2016 JL (Talk | contribs) uploaded "File:826 counter timing.png" (Timing diagram for 826 counter channel)
• 06:33, 9 June 2016 JL (Talk | contribs) uploaded "File:826 serial data capture.png" (Using an 826 counter channel to capture data from a serial data source. Each data edge causes a counter snapshot that contains a reason code and timestamp.)
• 10:10, 3 June 2016 JL (Talk | contribs) uploaded "File:826 quadrature gen.gif" (Using two counter channels to generate quadrature output)
• 09:32, 26 May 2016 JL (Talk | contribs) uploaded "File:2410.jpg" (Model 2410 is a compact open-frame module that interfaces 48 general-purpose TTL/CMOS compatible digital input/output (DIO) signals to Ethernet.)
• 09:51, 11 May 2016 JL (Talk | contribs) uploaded a new version of "File:826PwmWatchdog.gif" (show inverted DIO output; label DIO_out router)
• 08:06, 11 May 2016 JL (Talk | contribs) uploaded "File:826PwmWatchdog.gif" (Simplified block diagram showing how to implement a PWM generator with watchdog-triggered fail-safe output on a Sensoray model 826 board.)
• 09:55, 29 March 2016 JL (Talk | contribs) uploaded a new version of "File:826 3Phase pwm.png" (corrected DIO channels)
• 09:09, 29 March 2016 JL (Talk | contribs) uploaded "File:826 3Phase pwm.png" (A 3-phase PWM generator implemented using 5 counter channels and 3 DIOs on a Sensoray model 826 board.)
• 11:39, 21 March 2016 JL (Talk | contribs) uploaded "File:518 power.jpg" (Power supply test points on model 518.)
• 11:48, 11 March 2016 JL (Talk | contribs) uploaded "File:518 photo.jpg" (Model 518 board)
• 15:56, 4 April 2014 JL (Talk | contribs) uploaded "File:2255 photo.jpg" (Model 2255)
• 15:41, 4 April 2014 JL (Talk | contribs) uploaded "File:826 photo.jpg" (Sensoray model 826 board)
• 15:31, 4 April 2014 JL (Talk | contribs) uploaded "File:2226 photo.jpg" (Sensoray Model 2226)
• 15:09, 25 April 2013 JL (Talk | contribs) uploaded a new version of "File:AdgGroundReference.gif" (cropped)
• 15:01, 25 April 2013 JL (Talk | contribs) uploaded "File:AdgGroundReference.gif" (When connecting an isolated source to an ADC, one of the source conductors must be referenced to the ADC's power supply ground.)