Difference between revisions of "7501T8"
From Sensoray Technical Wiki
|
|
| (33 intermediate revisions by one user not shown) |
| Line 1: |
Line 1: |
| − | Model 7501T8 is a solid-state relay (SSR) rack that accommodates up to eight G4 type SSR modules. It has a 50-pin header which is compatible with several Sensoray GPIO products, including models 826 and 2410.
| + | #REDIRECT [[7501Tx relay racks]] |
| − | | + | [[Category:Products]] |
| − | ==Pinout==
| + | |
| − | | + | |
| − | {| class="wikitable"
| + | |
| − | ! SSR
| + | |
| − | ! Header<br>Pin
| + | |
| − | ! Terminal<br>Block Pins
| + | |
| − | ! Model 826<br>J3 GPIO
| + | |
| − | ! Model 826<br>J4 GPIO
| + | |
| − | ! Model 2410<br>GPIO
| + | |
| − | |-
| + | |
| − | |0
| + | |
| − | |47
| + | |
| − | |1-2
| + | |
| − | |0
| + | |
| − | |24
| + | |
| − | |17
| + | |
| − | |-
| + | |
| − | |1
| + | |
| − | |45
| + | |
| − | |3-4
| + | |
| − | |1
| + | |
| − | |25
| + | |
| − | |19
| + | |
| − | |-
| + | |
| − | |2
| + | |
| − | |43
| + | |
| − | |5-6
| + | |
| − | |2
| + | |
| − | |26
| + | |
| − | |21
| + | |
| − | |-
| + | |
| − | |3
| + | |
| − | |41
| + | |
| − | |7-8
| + | |
| − | |3
| + | |
| − | |27
| + | |
| − | |23
| + | |
| − | |-
| + | |
| − | |4
| + | |
| − | |39
| + | |
| − | |9-10
| + | |
| − | |4
| + | |
| − | |28
| + | |
| − | |9
| + | |
| − | |-
| + | |
| − | |5
| + | |
| − | |37
| + | |
| − | |11-12
| + | |
| − | |5
| + | |
| − | |29
| + | |
| − | |11
| + | |
| − | |-
| + | |
| − | |6
| + | |
| − | |35
| + | |
| − | |13-14
| + | |
| − | |6
| + | |
| − | |30
| + | |
| − | |13
| + | |
| − | |-
| + | |
| − | |7
| + | |
| − | |33
| + | |
| − | |15-16
| + | |
| − | |7
| + | |
| − | |31
| + | |
| − | |15
| + | |
| − | |}
| + | |
| − | | + | |
| − | ==Using with model 826==
| + | |
| − | | + | |
| − | {| class="wikitable" style="float:right"
| + | |
| − | |+GPIO mapping for model 826
| + | |
| − | ! rowspan="2"|SSR
| + | |
| − | ! colspan="2"|826 GPIO
| + | |
| − | |-
| + | |
| − | ! J3
| + | |
| − | ! J2
| + | |
| − | |-
| + | |
| − | |0
| + | |
| − | |0
| + | |
| − | |24
| + | |
| − | |-
| + | |
| − | |1
| + | |
| − | |1
| + | |
| − | |25
| + | |
| − | |-
| + | |
| − | |2
| + | |
| − | |2
| + | |
| − | |26
| + | |
| − | |-
| + | |
| − | |3
| + | |
| − | |3
| + | |
| − | |27
| + | |
| − | |-
| + | |
| − | |4
| + | |
| − | |4
| + | |
| − | |28
| + | |
| − | |-
| + | |
| − | |5
| + | |
| − | |5
| + | |
| − | |29
| + | |
| − | |-
| + | |
| − | |6
| + | |
| − | |6
| + | |
| − | |30
| + | |
| − | |-
| + | |
| − | |7
| + | |
| − | |7
| + | |
| − | |31
| + | |
| − | |}
| + | |
| − | | + | |
| − | The relay rack can be connected to header J3 or J2 on the 826 board. The GPIO associated with each SSR depends on whether the relay rack is connected to J3 or J2, as shown in the GPIO mapping table.
| + | |
| − | | + | |
| − | You must supply 5 VDC power to the relay rack. This can be done in either of the following ways:
| + | |
| − | * Connect an external 5 VDC power source to the relay rack's +5V and GND terminals.
| + | |
| − | * Attach a wire on the bottom of the relay rack (via solder) from the +5V terminal to J1 pin 49.
| + | |
Latest revision as of 13:28, 19 February 2019
- REDIRECT 7501Tx relay racks